Napoleon Grills N415-0158 Bedienungsanleitung

N415-0158 APR 11/07 NAPOLEON APPLIANCE CORPORATION.,214 BAYVIEW DR., BARRIE, ONTARIO, CANADA L4N 4Y8 PHONE: (705)726-4278FAX: (705)725-2564 EMAIL

10Problem Possible Causes SolutionLow heat / Low flame whenvalve turned to high.For propane - improper lightingprocedure.Ensure lighting procedure is

11ORDERING REPLACEMENT PARTSBefore contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance,trouble

12ASSEMBLY INSTRUCTIONSCAUTION: During unpacking and assembly it is recommended that you wear work glovesand safety glasses for your protection. Alth

1316 XN570-0073 (1/4-20 X 3/8”)3/816 XN450-0027 (1/4-20)Caster Installation1 Magnet InstallationSnap magnets into slots in front of bottom shelf.27/16

144 XN570-0080 (#14 X 1/2")3/84Left and Right Cart Panel InstallationInstall end cart panels ensuring slots in panel are to the top, rest panel o

15PROPANE ONLY66 XN570-0080 (#14 X 1/2")3/85Fit rear cart panel between the two end panels, ensure large hole in panel is tothe bottom right hand

164 XN570-0080 (#14 X 1/2")DRAWER/HOUSING INSTALLATIONPlace complete drawer housing assembly onto bottom shelf lining up holes inhousing with hol

173/8PROPANE ONLY9Propane Tank Heat Shield InstallationAttach propane tank heat shield above propane tank ring. Attach one end underlip of back panel

18TWO PEOPLE ARE REQUIREDFOR THIS STEP6 xN570-0073 (1/4-20 x 3/8”)3/810Grill Head Installation PROPANE ONLY - To avoid assembly difficulties,

1912Insert (4) 1/4-20 x 5/8” screws through washers into threaded holes in side ofbase, do not tighten all the way. Slide assembled side shelf over s

2NAPOLEON products are designed with superior components and materials, and are assembled by trainedcraftsmen who take great pride in their work. The

20Side Burner Installation3/813Insert (4)1/4-20 x 5/8” screws through washers into threaded holes in side of base.Do not tighten all the way. Slide a

213/814 Assembling Side EnclosuresTake (1) side enclosure panel and place on solid surface. Fasten top and bottomto side using (8) #14 x 1/2” screws.

22BUSHING8 x N120-0010THREAD CAPSAttach the supplied thread caps to the threads of the screws inside yourgrill cabinet as illustrated, both top and bo

23Insert pivot rod through hole on inside top of door. Holding door in one hand,direct pivot rod into hole in underside of front beam. Once secure,

24Insert pivot rod through hole on inside top of door. Holding door in one hand,direct pivot rod into the top bushing on the enclosure. Once secure,

25Postion grills and warming rack into base as shown. Rest warming rack onbrackets inside hood and grills on front and back lip of base.Sear Plate ,

26Grease Tray and Holder Installation22Clip the wire grease tray holder into the two holes located in the center of theback panel. Place the aluminum

27CLIP HOSE TO SIDE PANEL USINGHOSE RETAINER CLIP SUPPLIEDPROPANE ONLY3/42 XNATURAL GAS ONLY1x105-0002CLIP HOSE TO SIDE PANEL USING HOSERETAINER CLIP

28A LEAK TEST MUST BE PERFORMED AT THEFOLLOWING TIMES:•BEFORE INITIAL USE EVEN IF THE GRILL WASDEALER ASSEMBLED.•AT LEAST ONCE PER YEAR.•WHENEVER ANY

29PARTS LISTx - standard p - propane units only p - appareils propane seulementx - compris n - natural gas units only n - appareils gaz naturel seulem

3SAFETY PRECAUTIONSDo not store or use gasoline or otherflammable liquids or vapor in the vicinity ofthis or any other appliance. An L.P. cylindernot

30PARTS LISTItem Part # Description 730N725-0037 rear burner valve n47 N475-0183P left / right side panel cabinet enclosure x48 N555-0018 door pivot

31

32NOTES

4NATURAL GAS HOOK-UP: This natural gas grill is supplied with a 10ft supply hose (complete with a quick disconnect)designed for natural gas and certi

5LEFTBURNERSIDEBURNERLEFTCENTERBURNERLIGHTING INSTRUCTIONSRIGHTCENTERBURNERThe propane cylinder is equipped with an excess flow device. Unless all bu

6OPERATING THE GRILLBURN IN PROCEDUREWhen lit for the first time, the gas grill will emit a slight odour. This is a normal temporary condition caused

7Most people don’t realize that the heat source that we are most familiar with, namely the sun warms the earth using mainly infrared energy.Infrared e

8If the burner is getting too little air, the flames will be lazy yellow, and possibly produce soot. If the burner is getting toomuch air, the flames

9 TUBE BURNER - The burner is made from heavy wall 304 stainless steel, but due to the extreme heat and corrosiveenvironment, surface corrosion will o